![]() We need to add a Switch patch to our Patch Editor. That is because a Tap only lasts for one frame, and triggers when you release your finger. You might see that it is triggering but not holding that state. Creating a new connection to an input will replace an older one. Try connecting the Tap output of the Interaction patch to the Number input of the Pop Animation patch. We would like this Transition to occur when we tap on Photo, not just when we press Down. Now when I tap and hold Down on Photo, this Transition is eased - or animated. ![]() You might start to see that everything in the Patch Editor flows from left to right. Insert the Pop Animation patch between the two existing patches by connecting the Down output of the Interaction patch to the Number input of the Pop Animation patch, and then the Progress output of the Pop Animation patch to the Progress input of the Transition patch. Press Return ⏎ when Pop Animation appears. Double-click on the Patch Editor ⌘ ⏎ and begin to type ‘animation’. The next thing we want to do is add animation. You should now see that pressing Down on Photo causes the Transition to occur instantly between 0.38 and 1. Like we did with connecting Down to Progress, we can make connections from patches to layer properties.Ĭlick and drag on the Transition output and connect it to the Scale property of Photo in the Inspector panel. We need to connect the Transition output to the Photo layer’s Scale property. Be sure you are connecting from the Down output. Do this by clicking and dragging from the Down output into the Progress input of the Transition patch. Start input should be 0.38 and End input should be 1.Ĭonnect the Down output of our purple Interaction patch to the Progress input of the Transition patch. Change the End input value to 1, since we know that’s the Scale we want Photo to end at. Make the Start input on the Transition patch equal 0.38 by typing 0.38 into the Start input field. Add this patch by double-clicking on the Patch Editor ⌘ ⏎, beginning to type ‘transition’, followed by Return ⏎. The next patch we want to add is a Transition patch, since we are transitioning between two values. A Scale of 1 and a Scale of whatever fits in screen, which is about 0.38. We want this to transition between two values of Scale. The first two outputs, Down and Tap, should flash when Photo is tapped. Both of these outputs flash corresponding to when Photo is pressed Down, and when released, which equals a Tap. We’ll cover patches in detail a little bit later on, but for now, keep an eye on the Down and Tap outputs whilst tapping on Photo in the Viewer. You’ll notice that this adds an Interaction patch to our Patch Editor. To add interaction to a layer, hover over the layer in the Layers panel, click the circle icon, and then click Tap. The first thing we want to do is add interaction to the Photo layer. Change the Anchor by clicking on the desired point, or by clicking and dragging to the desired point. ![]() Let’s fix that by selecting the Photo Layer and Info Group and dragging to the left until those layers are centered. The Origami Studio interface.Īfter pasting in from Sketch or Figma, you may have noticed that our layers got misaligned slightly. ![]() The middle area is split between the Canvas on the top and the Patch Editor on the bottom. On the right hand side is the Inspector which lists the properties of the currently-selected layer. To the right of that is the Viewer where we see and interact with our prototype. On the left side of the screen is the Layer List, where we see the layers from the Canvas. In a new Origami prototype, navigate to Edit > Paste or use the keyboard shortcut ⌘ V. Click Copy Selected Layers from the Origami plugin. Open the Origami Figma plugin from the Plugins menu then select the Photo layer (a landscape image of the Golden Gate Bridge) and Info Group (which contains a few text layers, an image, and a gradient). fig lesson file by dragging and dropping into Figma then open the file in Figma. With our Sketch layers already on the macOS Clipboard.įirst make sure you have the Origami Pasteboard installed from the Figma plugin community. In a new Origami prototype, navigate to Edit > Paste ⌘ V. Copy those layers by going to Edit > Copy or using the keyboard shotcut ⌘ C. Next, select the Photo layer (a landscape image of the Golden Gate Bridge) and Info Group (which contains a few text layers, an image, and a gradient). First off, make sure you have the Sketch file from our lessons file open. Importing from design tools like Sketch is as simple as copying and pasting. Follow along by downloading the files that accompany this tutorial. We’ll be building a simple prototype, and by doing so learn the fundamentals of using Origami as well as importing from design tools such as Sketch. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |